HB-Digital Sat Finder for adjusting your digital or analogue satellite system This digital SAT FINDER is microprocessor-controlled and therefore reliable and precise. The signal strength is shown graphically on an LCD display in the form of a thermometer scale and in numbers (0-99). In addition, the unit can emit high-pitched tones via a buzzer (the higher the tone, the better the signal). This digital SAT FINDER is very sensitive and can detect even the weakest signal. Strong input signals (from powerful satellites, large satellite dish) can easily be attenuated for better reading.
It is simply connected between LNB and receiver via connection cable.
Technical data:
- Input frequency: 950-2150MHz
- Input level min.: -40dBm
- Input level max.: -10dBm
- Input impedance: 75 Ohm, F-connector
- Operating range: 52~60dB
- Power supply: DC 13-18V
- Size: 13x6,8x2,5cm (LxWxH)
- Screen size: 5.7x 1.7cm (LxW)
Specifications:
- Under the following test operations: LNB gain = 55dB, Carrier C/N = 15dB
- Insert a 5dB attenuator when operating an LNB with a gain of 60~65dB
Quick guide:
- Connect the LNB cable to the "Satellite" marked connector on the SAT Finder
- Connect the cable from the receiver to the connection marked "Receiver"
- On the receiver, select the station or transponder whose signal quality you want to improve
- Turn the rotary knob on the side until the display shows approx. 50% of the signal strength
- Turn the SAT dish slowly until the signal strength increases. Then reduce the signal strength again to approx. 50%. Repeat the process until the signal strength no longer increases
Special features:
- Built-in compass
- LCD screen
- LED backlight
- Digital display
- Very easy operation Scope of delivery
Scope of delivery:
- 1 x Sat - Finder with gold-plated connections
- 1 x instruction manual
- 1 x F-connection cable (short)
HB-Digital Sat Finder for adjusting your digital or analogue satellite system This digital SAT FINDER is microprocessor-controlled and therefore reliable and precise. The signal strength is shown graphically on an LCD display in the form of a thermometer scale and in numbers (0-99). In addition, the unit can emit high-pitched tones via a buzzer (the higher the tone, the better the signal). This digital SAT FINDER is very sensitive and can detect even the weakest signal. Strong input signals (from powerful satellites, large satellite dish) can easily be attenuated for better reading.
It is simply connected between LNB and receiver via connection cable.
Technical data:
- Input frequency: 950-2150MHz
- Input level min.: -40dBm
- Input level max.: -10dBm
- Input impedance: 75 Ohm, F-connector
- Operating range: 52~60dB
- Power supply: DC 13-18V
- Size: 13x6,8x2,5cm (LxWxH)
- Screen size: 5.7x 1.7cm (LxW)
Specifications:
- Under the following test operations: LNB gain = 55dB, Carrier C/N = 15dB
- Insert a 5dB attenuator when operating an LNB with a gain of 60~65dB
Quick guide:
- Connect the LNB cable to the "Satellite" marked connector on the SAT Finder
- Connect the cable from the receiver to the connection marked "Receiver"
- On the receiver, select the station or transponder whose signal quality you want to improve
- Turn the rotary knob on the side until the display shows approx. 50% of the signal strength
- Turn the SAT dish slowly until the signal strength increases. Then reduce the signal strength again to approx. 50%. Repeat the process until the signal strength no longer increases
Special features:
- Built-in compass
- LCD screen
- LED backlight
- Digital display
- Very easy operation Scope of delivery
Scope of delivery:
- 1 x Sat - Finder with gold-plated connections
- 1 x instruction manual
- 1 x F-connection cable (short)